CARDAS BINDING POSTS  

 








These beautifully made binding posts are fashioned from pure Tellurium-Copper alloy. The Gold/Rhodium model has a jewelry-like appearance. Either version achieves a notable sonic improvement. The 'nut' part can be 'backed off' and completely removed so you can easily get two or more spade lugs mounted on the post or even "ring" lugs will slide onto the posts. The hole in the ends accommodate any 'Banana' plug. Don't be confused a "pair" is enough to do one stereo amp.


If you have access to an appropriately sized step drill and a fairly stout electric drill that would be the preferred tool to enlarge the original hole. If it already has a 1/2” D-shape hole, file out the flat side with a round section file or make the Cardas insulator a "D" shape.



Advice for installers:  These binding posts require two 1/2" dia. mounting holes on 3/4" centers. Original mounting holes in the chassis of Hafler DH-200/220 and Hafler XL-280 are on 3/4" centers, but the holes must be enlarged. The DH-500 and XL-600 have "D" shaped holes of the correct diameter and you merely modify them to a round hole or the mounting plate to a "D" shape.


Important Note:  If the original holes in your chassis are less than 1/2" and you decide to skip enlarging the hole to save time and effort, just because the 'bolt' part of the posts fits thru the hole in the chassis, beware. If your new binding posts form a 'short-circuit' to ground, you amplifier may be destroyed when you first turn on your modified amp. At the very least, it will not work correctly under short-circuit conditions. Do it right! You guessed it, I mention that because I’ve seen that on our repair bench before.


Cardas Copper Binding Posts (CCBP):  $119.00/pr installed*, $69.00/pr for parts only


Cardas Gold/Rhodium Binding Posts (CCGR):  $125.00/pr installed*, $75.00/pr for parts only 


Advice for installers: These require a minimum 1/2"(0.500") mounting hole (if using the insulators) - 0.550" hole is fine. Smaller holes can be easily enlarged with a round section metal file. Some existing holes are a “D” shape and just need rounding out.


*Typical pricing for many amplifiers, more difficult installations may incur higher cost.


If you have one and are experienced with it, a Dremel® Moto-Tool works great here. A ceramic tile cutting bit is great for this chore, but they are made from brittle Tungsten-Carbide and can be easily broken when you are reaming metal. The Dremel Tool can be a great help, but requires some skill. You can do disturbing damage to your chassis in an instant, so practice on a piece of scrap metal, if you buy one of these very useful tools.


ALWAYS wear eye protection goggles when using any power tool! Remember how "MOM" said, you only get two eyes!




CARDAS GOLD/RHODIUM RCA JACKS


Short RCA Female, non-magnetic, eutectic Brass, Rhodium over Silver plate.

Comes standard with thin (.0135"), gold plated hex nut, Teflon insulation.

Supplied with red & white washers for channel identification.

Teflon® is a registered trademark of E. I. Du Pont


Cardas GRFA-S w/thin nut $27.00/pair as kit, typical $59/pr installed*





COPPER BASE, BEAUTIFULLY MADE GOLD-PLATED, TEFLON® RCA JACKS by CMC



These beautiful CMC RCA input connectors are the fine sounding Gold RCA jacks with a jewelry-quality appearance. High quality brass housing. The fastening nut is installed from outside of the chassis. Color-coded plastic insulating washers and mounting hardware are included. 


CMC Gold RCA: $19.00/pr parts only, $49.00/pr installed*

 

*Typical pricing for many amplifiers/preamplifiers, more difficult installations may incur higher cost.




Notes for installers - all RCA jacks


Critically Important Fact: Remember that your original RCA jacks may be insulated from the chassis or actually 'hard-grounded' to the metal without insulating hardware. When you install new jacks always observe this important fact. Some equipment may 'make' an important circuit ground via the RCA jack ground shell. The equipment may function improperly if new RCA jacks are not installed in the same electrical manner as the originals. Paying close attention, before smelling smoke, is always the best policy!!!!



Advice for installers: These require a larger than stock mounting hole in most cases (especially if using the insulators). Smaller original holes can be easily enlarged with a round section metal file, a reamer or a step-drill with some caution.

ALWAYS wear eye protection goggles when using any power tool!

Great Sounding Connectors